Van/Truck Specifications
BODYWORK
GRP bodywork conversion with fully insulated roof sections and lined in easy clean laminate. The special method of body construction, builds in extra strength, yet reduces overall weight of vehicle, due to the use of GRP which will not corrode.
Two roof vents are fitted with adjustable openings for extra ventilation. Air Conditioning is available as an option.
Serving windows in polished aluminum frames are fitted to either side of the vehicle. The sliding opening windows can be modified to suit any opening required, i.e. from 18"x22" up to 32"x40". (This is because local authorities interpret hygiene laws differently.)
A fixed rear window is fitted in polished aluminum frame.
All window glass is in toughened glass and can be supplied in various tints if required.
Illuminated louvers are fitted at either side above the serving windows and at front of vehicle, these are illuminated by fluorescent tubes from inside and are sign written to increase nighttime advertising.
Two illuminated ice cream cones are fitted to front of vehicle.
Painting and sign writing are to customer’s own choice and specification. An outline of the vehicle will be supplied for owner design requirements.
INTERIOR FITTINGS
A 24 cubic foot holdover (cold plate) deep freezer is fitted across rear of vehicle with 4 flip-flop lids on top. The eutectic plates in this deep freezer ensure that a temperature of –10F or less is maintained in normal daily use. The holdover system requires that the 1HP condensing unit, fitted in the rear of the vehicle, is plugged into mains electricity for at least 8 hours or more (overnight) per 24 hours.
A 14 cubic foot holdover chill storage fridge is fitted behind the drivers’ seat. This has 2 doors at front and can be fitted with shelves as required. Temperatures are again maintained by eutectic holdover plates. The chill storage is used for the storage of soft serve mix and for cold drinks. All refrigeration units are constructed in 304-grade stainless steel and are more than adequately insulated with polyurethane foam insulation.
Three stainless steel wash sinks and drainer are fitted in the cab area of the vehicle. These are supplied with hot and cold running water via a mixer faucet tap from a 30-gallon fresh water tank by a pressurized water system. Hot water is provided by a 5-gallon calorifier heated by the vehicle engine. A stainless steel hand wash sink with hot and cold water is located beneath the counter in the serving area adjacent to the soft ice cream freezer. A 35-gallon wastewater tank with drain tap is located beneath the vehicle floor. The serving are is completely separated from the drive cab with a full partition fitted with a self-closing door.
The soft serve ice cream machine is mechanically powered via a power take-off from the vehicle drive engine. This system does not require any electrical power other than the 12volt DC system of the vehicle for the machine control circuits. This system has been produced and used by the production company for over 35 years and has been sold to over 45 countries worldwide. This system is very reliable and does not require the vehicle to carry a heavy generator to power the soft serve machine. This also makes the operation very economic and simple to maintain, requiring only regular engine servicing.
Furthermore, since the vehicle engine is driving the equipment at an idle speed, great fuel economy is achieved.
Interior lighting is by 2 fluorescent light tubes fitted at either side covered with diffusers.
All work surfaces are in stainless steel or easy clean laminate.
The floor is in heavy-duty non-slip altro flooring on top of an exterior grade ply floor to provide an easy clean hygienic surface.
All products used are of the highest quality available. The Production Company has over 40 years of experience and has attained the status of world leader in the construction of mobile vending units and has been the envy of the trade. Company policy has been to maintain the position of world leader by continuously upgrading quality and workmanship.
There are thousands of vehicles all over the world that are over 20 years old and are still operating profitably and successfully.
In the event of spares being required, most are commonly available all over the world, however, should the need arises for a specific part not found locally, immediate shipment is made from the plant by express or overnight service. Our guarantee is that your unit will operate as specified for many years to come creating repeat customers from the profits earned by using these great money making
